Unfortunately we only offer Solera Awnings and components, which are not compatible with Dometic awnings so the only thing we could offer you would be a completely new awning like the Solera Smart Arm 12V Power RV Awning # LC517505. You can reach out to Dometic directly to see if they can offer you replacement parts, but with everything you're needing the cost of each item separately might end up being the same or more than just completely replacing the awning. If you end up swapping out... view full answer...
From our research your 2009 Keystone Fuzion travel trailer has Venture landing gear on it from the manufacturer. You should be able to use the Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear part # LG-179014 to replace your follow leg but you want to make sure your leg measures 29-1/2". Since you cannot get to the landing gear, if you can find a brand of the landing gear it would be very helpful. view full answer...
From what I could find on the 2010 Keystone Fuzion Toy Hauler 405, it has 7,000 lb. ez lube triple axles that are already flipped. Given that information, the only thing that we would have is the Correct Track Trailer Alignment and Lift Kit # LC87120 (you would need one kit for each axle). This will provide you with 2-1/4" of lift.
You can try lowering the pin box to try and make up the other 2" you are needing, but it sounds like you may be dealing with a lifted truck which can often... view full answer...
The height of the outer tubes on the Landing Gear Set - 36-1/2" Lift - 8,000 lbs # RVLG-8000 is roughly 29" without the legs and 32-3/4" with the drop legs included. The distance between the outer edges of the top and bottom weld stops is 17-1/2" and the distance between the inner edges is 15-1/2". This will be important to know since it's where the landing gear will mount to your coach, so you'll want to know the distance between the weld stops where your current landing gear are mounted. view full answer...
The correct replacement circuit and control board for your Lippert Electronic leveling system is the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System # LC421484. This will be a plug and play solution, so it's easy to install and will not require any type of programming. view full answer...
Hello Robert. For that I suggest using butyl tape and non-sag sealant. For butyl tape I recommend the Alpha Systems Butyl Tape for RV Weatherproofing # AL28FJ. This is a 20' long roll of 1" thick tape.
For sealant I recommend the Alpha Systems 1010 Non-Sag Sealant for RVs # AL53KV. This is a single 10.3 oz tube non sag sealant and it is black in color. So, it will go perfectly with the Jensen # MSX60RVR marine speakers you were looking at.
I have linked our video for these speakers... view full answer...
Hey Pam, so the trick to picking out RV roof vent lid replacements is the hinge of the lid. So if the hinge you have looks like the # BVD0449-A01 then this for sure is the correct replacement. view full answer...
The best replacement option we have for your discontinued Dometic DOTR12CBIV Over-the-Range Microwave , is the Greystone Standard RV Microwave w/ Trim Kit # 324-000106.
The dimensions of this option without trim kit are 19" wide x 12" tall x 14-1/4" deep. With the trim kit, 23-3/8" wide x 15" tall x 14-1/4" deep.
Please note the linked product review video below. view full answer...
I suggest the Stromberg Carlson RV Exterior Ladder w/ Hinges, # LA-401BA for black or, # LA-401 in aluminum finish with dimensions of 99-1/2" tall x 12 wide.
Please keep in mind that the RV exterior ladders we offer are not exact OEM replacements but are general-application items that function perfectly well with most RVs. We do not have the ability to pull a build sheet from the OEM's for their original part numbers installed. Occasionally some RV's are constructed with a custom ladder... view full answer...
So what you could do is use the coiled tow bar wiring kit from Blue Ox part # BX8861 at the rear of the fifth wheel that has a 4-way flat connector as this comes with a 4-way round connector that can replace it as well as another one for the front of your tow vehicle and coiled wiring to connect across the tow bar.
Then for an easier to install invisible supplemental braking system the Demco SBS DUO part # SM99251 would work great.
I don't know the year of your Chevy Spark for determining... view full answer...
Yes, the LaSalle Bristol CrossBreeze Screen, # 3441409775PBK is attached to the inside wall of your toy hauler. The inside-wall-to-inside-wall measurement is what is crucial for fitment. For your RV, you provided a measurement of 98-1/2" so the 97-3/4" wide, # 3441409775PBK is what you will need.
There is not an option to disassemble and cut width for fitment.
When installing, you will need to fit within the walls of your RV and build-up the gap by using spacers, running a strip of lumber... view full answer...
The only other thing I can think of is that the brakes might not be adjusted correctly. On the back of your brakes there will be an oblong hole with a plug in it. This is where you'll adjust the brakes using a brake adjustment tool # W80630.
You'll need to get the trailer onto some jack stands so the brakes can be spun freely. From here, you'll need to grab the teeth on the star wheel and run the brake shoes out until they don't spin by hand anymore. Once you're here, go ahead and back... view full answer...